Hull & Deck
•  J/121 hull & deck are vacuum-infused molded (SCRIMP process) in temperature controlled environment with biaxial and unidirectional E-glass fabrics using end grain balsa core in the hull for rugged durability and Corecell foam core in the deck for light weight.  High density core inserts and additional glass reinforcements are placed in way of highly loaded hardware and components.
•  Laminates are engineered and built to exceed ISO 12215 Cat A and ABS structural standards.
•  White gelcoat hull
•  Molded companionway seahood with slider.
•  ORC molded-in toe-rails forward of the mast.
•  GRP molded main bulkhead – structurally bonded and tabbed to the hull and deck with single large opening to forepeak.
•  Two watertight bulkheads (one in the forepeak and one forward of the steering system) bonded and tabbed to the hull and deck.
•  Heavy duty molded fore/aft and transverse keel support grid, with substantial composite structural beams.
•  Composite mast bearing beam with carbon fiber compression post, bonded and fastened to the deck.
•  High aspect, low VCG "IRC" keel with lead ballast and epoxy faired and finished fin, flange mounted to a hull recess.

Mechanical & Steering
•  Yanmar 3YM30ACE 3 cylinder 4-stroke 29hp diesel engine with 125 amp alternator and SD 25 Saildrive with 2-piece split zinc.
•  Yanmar keyless digital B instrument panel mounted in recess on cockpit wall near wheel
•  Gori three blade, geared folding prop.
•  Spinlock flush mount engine throttle control with removable handle and neutral safety switch.
•  Balanced spade, composite rudder with stainless rudder post mounted in self aligning, Jefa rudder bearings w/ Jeffa Pilot Drive
•  Jefa twin pedestal steering system including sheaves, radial drive, needle bearings, and integral wheel brake.
•  Carbonautica custom composite wheels (2) finished in black Awlgrip.
•  Emergency tiller.

Deck Hardware
•  Harken Performa 52:1 self-tailing primary winches.
•  Harken Performa 46:1 self-tailing cabin top winches.
•  Harken Performa 46:1 self-tailing mainsheet winches.
•  Four Harken One-touch winch handles.
•  6:1 Harken traveler system on cockpit floor.
•  Adjustable jib lead system with floating lead blocks and inhaul and outhaul capability.
•  Cascading cunningham system led to cockpit.
•  Harken spinnaker sheet and tack line blocks.
•  Bow-sprit control system led externally to clutch mounted on cabin top.
•  Mast base halyard blocks and organizers.
•  Halyard & tack line rope clutches.
•  Custom mast collar with attachment points for halyard and mast base blocks, and halyard bale.
•  Stainless cabin top handrails P&S.
•  Tapered SS lifeline stanchions.  Forward stanchion with integral roller (P&S) for quick jib skirting. Double 1x19 stainless wire lifelines to meet all categories of the Offshore Special Regulations (OSR).
•  Custom bow pulpit and dual corner stern rails with LED navigation lights.
•  Antal Bow Cleats & Pop Up Aft Cleats
•  Interior ventilation from four framed opening ports in sides of cabin trunk, one offshore skylight deck hatch aft of mast, and one large offshore deck hatch forward of the mast.
•  Acrylic offshore drop-board with inside/outside lockable hasp.
•  Four polypropylene mesh line bags.
•  Custom SS forestay, shroud and backstay chainplates.

Plumbing & Electrical
•  24-gallon fuel tank with baffles and inspection port & additional 12 gallon fuel tank
•  12-gallon head holding tank.
•  Raritan PH-II head with deck pump-out.
•  Manual fresh water system with 26-gallon water tank and manual pumps and spigots in the galley and head and Whale 6 gallon hot water tank.
•  Cockpit operated manual bilge pump.
•  Three105 amp deep-cycle, Group 31 sealed AGM batteries.
•  Three position battery switch.
•  Electrical panel w/circuit breakers.
•  Bonding system.
•  Five low profile, LED reading lights.
•  One adjustable red/white light in Nav station
•  Six red/white LED dome lights
•  Automatic bilge pump with manual/auto panel switch & Whale Supersub 12v 1100gph Low Profile Automatic bilge pump
•  Below deck OSR manual bilge pump.

Spars & Rigging

• Carbon fiber, auto-clave cured mast with double swept back spreaders, backstay crane, flush shroud terminations, sheaves for 1 main, 1 inner jib/staysail, 2 jib & 2 spinnaker halyards, vang and boom gooseneck fittings, steaming/foredeck light, masthead anchor/Tri-color light, internal wiring conduit, aluminum masthead bracket for owner provided wand. Antal mast track and loader gate. Mast/boom finished in black with contrasting white measurement bands.
• Carbon fiber, racing boom with 12:1 internal outhaul, one mainsheet block bale, vang lug, and sheaves for two reef lines and outhaul.
• Nitronic 50 discontinuous rod rigging package including shrouds and forestay.
• Adjustable open body shroud turnbuckles.
• DSK-90 Dyneema backstay connected to Harken integral hydraulic backstay adjuster operable on centerline just aft of the helm.
• Jib roller furling system.
• Carbon fiber bow sprit with internal bearing system and black painted finish. Fully extended position is supported by a Dyneema bobstay. Stored position is retracted aft of the stem for safer docking and maneuvering.
• Running rigging package with GP78 Main halyard, V100 Jib halyard, GP78 spin/Code 0 halyard, one Inner Jib Halyard with integral halyard lock, 2nd spinnaker halyard, one mainsheet, two reef lines, two jib sheets, and two spinnaker sheets. Also includes cunningham, boom vang, outhaul, pole control, 2 tack lines, inhauler and floating jib ring lines, and traveler control lines.
• Rigid boom vang with control lines led P&S to cockpit.

Sails - Complete UK inventory - New 2018 - (used two seasons)

Mainsail - Uni-Titanium LS w/three reefs
Delivery mainsail - 90oz CB Dacron w/ four battens
J1, J2, J3 - Uni Titanium LS
Code Zero - CZ 30 w/top down furling cable
A1 VMG - Superkote 60
A2 Runner - Superkote 75
A3 Reacher - Superkote 90 w/top down furling cable
A5 Runner - Superkote 90
Storm Jib and Trysail - 10oz CB Orange Dacron - (Storm jib w/ furling cable)